Các Lỗi về máy Doosan, Liên hệ Namfare 0522388776 để thực hiện sửa chữa các loại máy móc:
1. Emergency Alarm …………………………………………………………………………………………3
1.1 2001 OP Emergency Stop PB or LS Off…………………………………………………………….. 3
1.2 2002 Main Spindle Servo Alarm ……………………………………………………………………….. 5
1.3 2003 Circuit Protector Trip……………………………………………………………………………… 12
1.4 2005 Hyd. Pressure Down Alarm ……………………………………………………………………. 14
1.5 2006 Gear Shift Check Switch Alarm (Gear Type Spindle) …………………………………. 17
1.6 2008 PSM Contact Check Error ……………………………………………………………………… 19
2. Cycle Stop Alarm………………………………………………………………………………………..21
2.1 2032 External Feed Hold (OP Push Button Switch) …………………………………………… 21
2.2 2033 Air Pressure down Alarm……………………………………………………………………….. 22
2.3 2034 Coolant & Lub. & ATC Motor Overload…………………………………………………….. 24
2.4 2036 Coolant W/Tank or Level Switch Alarm………………………………………………….. 27
2.5 2037 Power Back Up Power Failure Alarm (Power Back Up Module Option)………… 28
2.6 2038 Spindle Lub.Level Low or Press. Down (1500rpm Option) ……………………….. 29
2.7 2040 Operator’s Door Open Alarm………………………………………………………………….. 31
2.8 2048 Spindle Stop Signal Alarm……………………………………………………………………… 32
2.9 2049 Spindle Speed Arrival Alarm…………………………………………………………………… 34
2.10 2050 Spindle Rotation Malfunction………………………………………………………………… 44
2.11 2051 Spindle Orientation Overtime………………………………………………………………… 46
2.12 2055 Spindle Tool CL/UNCL Overtime Alarm………………………………………………….. 48
2.13 2056 Gear Shift Overtime Alarm (Gear Type Option) ……………………………………….. 51
2.14 2058 Tool No. Select Keep Relay Not Set………………………………………………………. 53
2.15 2059 Tool Search Illegal Position ………………………………………………………………….. 57
2.16 2060 M06 Command Illegal Position……………………………………………………………… 60
2.17 2061 T-Code Command Over Alarm ……………………………………………………………… 64
2.18 2062 M06 Command Overtime Alarm ……………………………………………………………. 66
2.19 2066 Spindle Air Pressure Down Alarm (1500rpm Option) ……………………………….. 72
2.20 2080 Spindle Head Oil Overflow (Gear Type Option)……………………………………….. 73
2.21 2133 Man Axis Moving Interlock ………………………………………………………………………….. 75
3. Single Block Alarm……………………………………………………………………………………..80
3.1 2160 Lubrication Oil Level Low ………………………………………………………………………. 80
3.2 2161 Lub. Pressure Alarm……………………………………………………………………………… 82
3.3 2162 Parts Count End Alarm………………………………………………………………………….. 84
1
Mynx 6500(ATC#50/F-32i)
M6500ALE0C
3.4 2164 Oil Cooling Unit Alarm…………………………………………………………………………….85
3.5 2166 Coolant Filter Change Alarm……………………………………………………………………96
3.6 2167 Flow Indicator Abnormal Alarm ………………………………………………………………..97
3.7 2168 Coolant Pressure Down Alarm…………………………………………………………………99
3.8 2170 Tool Life Management End Alarm …………………………………………………………..100
3.9 2171 RST Command Alarm On STL……………………………………………………………….101
3.10 2179 Spindle Head Oil Pumping Alarm (Gear Type Option) ……………………………..102
3.11 2182 Side Window Door Open……………………………………………………………………..105
4. Massage Alarm………………………………………………………………………………………… 107
4.1 2190 Drum Filter Chip Coolant Low Level ……………………………………………………….107
4.2 2192 Tool Monitor Warning Alarm …………………………………………………………………..108
4.3 2193 Safety Switch Locking Alarm………………………………………………………………….109
4.4 2195 OP-Door Close, Must By D-Open ………………………………………………………….. 111
4.5 2196 Screw Conveyor / Oil Mist Overload ………………………………………………………. 112
4.6 2197 Chip Conveyor Alarm ……………………………………………………………………………114
4.7 2198 Auto Power Off Ready ………………………………………………………………………….115
4.8 2200 The Warming Up is Not Complete…………………………………………………………..116
4.9 2201 Wait for Spindle Lubrication …………………………………………………………………..118
4.10 2202 Machine Lock on Status………………………………………………………………………120
4.11 2204 Feedrate Override 0% …………………………………………………………………………122
4.12 2205 Low Battery for Measurement(Option Renishaw Tool Measurement)…………124
4.13 2206 Work Measurement Probe Error(Option Renishaw Tool Measurement) ……..125
4.13 2208 Message In Service Mode……………………………………………………………………126
4.14 2216 Return to Ref. Point for X-Axis ……………………………………………………………..127
4.15 2217 Return to Ref. Point for Y-Axis ……………………………………………………………..128
4.16 2218 Return to Ref. Point for Z-Axis ……………………………………………………………..129
4.17 2230 Spindle Stop In Cutting Mode Command……………………………………………….130
4.18 2234 Gear Shift Lost (Gear Type Option) ………………………………………………………132
4.19 2250 ATC OP Manual Mode ………………………………………………………………………..134
4.20 2251 ATC Overtime…………………………………………………………………………………….135
4.21 2252 ATC Interlock Alarm ……………………………………………………………………………138
4.22 2253 Changer Arm Position Check Alarm………………………………………………………140
4.23 2260 ATC Magazine Rot. Overtime Alarm ……………………………………………………..143
4.24 2261 Tool Magazine Synchro Malfunction ……………………………………………………..146
4.25 2262 ATC Magazine Guard Door………………………………………………………………….149
4.26 2274 Wait. Pot(Mag.) Spd/Mag. Side Alarm……………………………………………………151